How To Lubricate Skateboard Bearings – It Is Time To Know

Maintenance of skateboards can be a bit steep for some people, therefore if you are on a budget, knowing how to lubricate skateboard bearings can help a lot. 

This guide will show you how to do the job properly. Read on to keep your bearings in tip-top condition for a smooth and enjoyable ride.

Lubricating the bearings is one of the most pivotal steps to help your skateboard run smoothly for a long time. No more hesitation and dive into this magic procedure.

The Tools You’ll Need

  • A skate tool, or a wrench, or a ½ inch socket
  • A razor blade or a pin (ideally something pointy)
  • Solvent
  • A container (a bowl perhaps)
  • Some rags
  • Lubricant

Typically, your greasing process will consist of the following steps:

Step 1: Dismantle the bearings

Step 2: Clean the bearings

Step 3: Lubricate

Step 4: Reassemble the bearings back on the skateboard

Only by dripping lubricant onto the outside of the parts can you simply fix many minor issues on your own. Now that you’ve got all the essential tools, let's move to the step-by-step guide.

Step 1: Dismantling

how to lube skateboard bearings

Bearing Being Separated From The Wheel

Start by removing the speed washers and nuts of the wheels from your skateboard using the skate tool or wrench. Remember to put the nuts together in one place to avoid losing them.

Next, take out the bearings from the wheels. You can do this by prying them out with the truck's axle. Try twisting the wheels off, leaving only the inner bearings and the spacers on the axle. Take the bearings off and flip the wheels and repeat this procedure for the outer bearings.

Once you have done this for all the wheels, remove the one shield of each bearing with a pointy object, such as a razor blade or a safety pin. Some of them have two shields, only pop the inner shield off and leave the outer shield alone.

Keep in mind not to bend the shields and not to lose them. If they have dirt on them, rub it off with your fingers or a piece of rag.

Step 2: Cleaning

how to lubricate skateboard bearings

Bearings Being Soaked

Fill up your container with water-based solvent or degreaser. Acetone is what we would go for. Next, put the bearings into the contrainter you have prepared. 

Let them sit in the solution for about 10 to 15 minutes. Occasionally shake the container or swirl the parts around. You can speed up this part by scrubbing the parts with a clean rag or a toothbrush within the solution. 

After taking the bearings out, use a clean drag to rub them carefully. Finally, spin them until they are all smooth and shiny.

See also: How To Clean Skateboard Bearings With Household Items

Step 3: Lubricating

how to lubricate bearings skateboard

Dripping Lubricant Onto The Bearings

Make sure that the bearings are dry before lubricating them. You can leave them to dry or gently tap them on rags or paper towels. Better yet, use a blowdryer to quickly evaporate any remaining solvent on the parts.

Then, you can grease them up. Skate-specific lubricants will be your best choice. Other safe and widely available alternatives include bike grease and motor oil. 

See also: Top 7 Best Lubricant For Skateboard Bearings in 2021

There are many ways to apply lubricants. You can add little drops of grease into the space between the balls. Or else you can dab a small spot of it on each ball, then spin the bearing with your fingers to spread the lubricant. 

Keep doing so until you evenly distribute the lubricant onto the parts.

Step 4: Reassembling

how to lubricate skateboard bearings

It’s Time To Reassemble Skateboard

Gently put the shields back on. All you need to do is set them in place and press. Be extra careful not to bend them. Similarly, put and press the bearings onto the wheels. The final step is to use the skate tool to put all the wheels and nuts back on the skateboard.

Conclusion

With that in mind, please remember not to overlook the importance of knowing how to lubricate skateboard bearings. Not only does it help save money and reduce friction damage but it also prevents water from entering and causing rusting.

We hope you find this guide helpful and get back on the board with functional bearings.

Related posts:

Click Here to Leave a Comment Below 0 comments

Leave a Reply:

Scroll Up